### Table 2 below shows the critical points, characterized by the bifurcation phenomenon that

"... In PAGE 13: ... Table2 : Critical load values obtained by test functions 5.3 Double braced rectangular frame The last structure to be analysed is a braced portal frame, Harrison 9 , shown in Figure 11.... ..."

### Table 2: Critical load values obtained by test functions

"... In PAGE 13: ...William Taylor Matias Silva 13 a b Figure 10: Deformed shapes: a - bifurcation point, b - limit point Table2 below shows the critical points, characterized by the bifurcation phenomenon that happens first. In this analysis it can be observed that the CSP did not detect the bifurcation point as expected and the least pivot did not detect the limit point.... ..."

### Table 1: Critical loads of a cylindrical shell with a cutout

2002

"... In PAGE 6: ...ig.3 shows the prebuckling deformation for cutout #1. As it was to be expected, the deformation due to axial compression is restricted mainly to the region around the cutout. According to Table1 , for both cutouts there is a single bifurcation point a0 a1a4a3 a5 a7 a6 along the equilibrium path before the limit load a0 a6 a3a8a9 a7 a6 is reached. The first buckling mode belonging to a0 a1a4a3 a5 a7 a6 obtained by a linearized bifurcation analysis is shown in Fig.... In PAGE 7: ...2 0.25 0 1 2 3 4 5 6 7 -5 0 5 Figure 5: Geometric imperfections mapped on the FE mesh a12 If bifurcation occurs at a load level higher than the bifurcation load of the perfect shell a0 a1a4a3 a5 a1a3a2a5a4 a5 (cor- responding to a0 a1a4a3 a5 a7 a6 in Table1 ) and the load step before is lower than a0 a1a4a3 a5 a1a3a2a6a4 a5 , then a0a2a1a4a3 a5 a1a3a2a6a4 a5 is assumed to be the critical load. In this case the imperfections do have no significant influence on the buckling behavior of the shell, implying that the imperfect shell behaves similar to the perfect shell.... ..."

Cited by 1

### Table 2. Critical Loads

"... In PAGE 5: ...Table2 summarizes the critical loads (in MW) for both the intact and disturbed system. As shown from the table, the in- tact system critical load is 4635.... ..."

Cited by 1

### Table 4: Critical Values of Bifurcations (b = ?0:7) Period Bifurcation-parameter: a

1996

Cited by 1

### Table 4: Critical Values of Bifurcations (b = ?0:7) Period Bifurcation-parameter: a

1996

Cited by 1

### Table 4: Critical Values of Bifurcations (b = ?0:7) Period Bifurcation-parameter: a

1996

Cited by 1

### Table 4: Critical Values of Bifurcations (b = ?0:7)

1996

Cited by 1

### Table IV. Critical crack lengths for bifurcation for 0.914-m long tubes.

2005

Cited by 1

### Table 8: Load representations and their critical clearing times.

"... In PAGE 4: ...3658 0.2244 In order to observe the effect of different load models in the results of the transient stability study, the active and reactive power consumed by the motor at the initial operating conditions are represented by the static exponential and polynomial characteristics dependent on voltage and frequency variations presented in Table8 [11,14,15]. The static exponential model dependent on voltage and frequency variations has the following parameters: pv = 0.... In PAGE 4: ...f = 2.9 and qf = 1.8 [11, 14]. The critical clearing times obtained after the digital simulations, for each load model, are shown in Table8... ..."